How to write latitude and longitude in degrees, minutes and decimals
Two numbers pin down any point on Earth. The NOAA observatory on Mauna Loa in Hawaii publishes its position as 19.5362° North, 155.5763° West. The same spot can be written 19° 32′ 10″ N, 155° 34′ 35″ W, and a reader who has met only one of these styles may not realize they match.
The numbers themselves are simple. The trouble comes from the formats, the order of the two values and the signs that mark hemispheres. One misplaced minus sign moves a point to the other side of the Equator or the prime meridian. This guide shows how the grid works, how to move between formats and how to check a pair of coordinates before you rely on it.
How the grid of latitude and longitude works
Latitude measures distance north or south of the Equator, which is 0°. Lines of equal latitude are called parallels, and they run from 90° south at the South Pole to 90° north at the North Pole. Longitude measures distance east or west of the prime meridian, the line through Greenwich, England, which is internationally accepted as 0°. Lines of equal longitude are meridians. They run from pole to pole, up to 180° east and 180° west. The 180° line is the basis of the International Date Line, which is covered in time zones and the date line.
Both are measured in degrees. Each degree divides into 60 minutes (′), and each minute into 60 seconds (″). National Geographic Education gives about 111 km for one degree of latitude. Longitude behaves differently, because meridians converge toward the poles. A degree of longitude is widest at the Equator, also about 111 km, and shrinks to nothing at the poles. The USGS publishes figures for 38° north that show the effect. The four hemispheres these lines create are described in hemispheres explained.
| Unit | Latitude (anywhere) | Longitude at the Equator | Longitude at 38° N |
|---|---|---|---|
| Degree | about 111 km | about 111 km | about 88 km |
| Minute | about 1.85 km | about 1.85 km | about 1.46 km |
| Second | about 31 m | about 31 m | about 24 m |
Four ways to write the same position
Coordinates appear in several styles, and all of them are correct when used consistently. The table writes one position, the Mauna Loa observatory as published by NOAA, in each style.
| Format | Example | How it works |
|---|---|---|
| Decimal degrees with letters | 19.5362° N, 155.5763° W | Degrees with a decimal fraction; hemisphere shown by a letter |
| Signed decimal degrees | 19.5362, -155.5763 | South and west are negative; latitude runs from -90 to 90, longitude from -180 to 180 |
| Degrees, minutes, seconds | 19° 32′ 10″ N, 155° 34′ 35″ W | Whole degrees and minutes; seconds rounded to whole numbers here |
| Degrees and decimal minutes | 19° 32.172′ N, 155° 34.578′ W | Whole degrees; minutes carry a decimal fraction |
Written pairs normally give latitude first and longitude second, although some software and data formats list longitude first. Rounding matters too. Rounded to whole seconds, the position above moves by about 10 m, and in the worst case half a second of latitude is about 15 m. That is harmless for a town and visible for a building. Symbols vary as well: the prime (′) marks minutes and the double prime (″) marks seconds, but plain apostrophes and quotation marks are common stand-ins. A comma or a space separates the two values.
Converting between formats step by step
- From degrees, minutes and seconds to decimal degrees: divide the minutes by 60, divide the seconds by 3,600 and add both results to the whole degrees.
- From decimal degrees to minutes and seconds: keep the whole degrees, multiply the leftover decimal by 60 to get minutes, then multiply the leftover decimal of the minutes by 60 to get seconds.
- Carry the hemisphere letter or the minus sign through the whole calculation, and put it back at the end.
| Decimal places | Approximate ground size | Suits |
|---|---|---|
| 1 | about 11 km | A large region |
| 2 | about 1.1 km | A town |
| 3 | about 110 m | A neighborhood |
| 4 | about 11 m | A building |
| 5 | about 1.1 m | A doorway |
Checking a coordinate pair before you use it
A pair that looks plausible can still be wrong by thousands of kilometers. A short check takes a minute and catches most errors. The same grid is used in the index of an atlas, as shown in how to read an atlas, and it stays the same on every projection, even though the lines are drawn differently, as explained in map projections.
- Confirm which value comes first. Latitude usually leads, but not in every program.
- Check the range. Latitude never goes beyond 90, and longitude never goes beyond 180.
- Look for letters or minus signs. Without them, a pair of positive numbers could mean four different places.
- Do not mix formats inside one pair, such as decimals for latitude and minutes for longitude.
- Match the number of decimals to the task, using the table above.
- Plot the point on a map and confirm that it falls in the right region.
Common mistakes with latitude and longitude
- Reading 19.30° as 19° 30′
The digits after a decimal point are a fraction of a degree, not a count of minutes. Multiply by 60 to convert them.
- Dropping the hemisphere or the sign
A pair without N, S, E, W or minus signs fits four places on Earth. Always keep one of the two marking systems.
- Swapping latitude and longitude
Values like 40 and 105 look plausible in either order. The range check helps only when one value exceeds 90, so confirm the order from the source.
- Assuming a degree of longitude is always 111 km
That holds only at the Equator. At 38° north, a degree of longitude is about 88 km, and it keeps shrinking toward the poles.
- Copying more decimals than the source supports
Eight decimals describe a point about a millimeter wide. If the original place was a town, the extra digits only add false precision.
Frequently asked questions
Which comes first, latitude or longitude?
In written coordinates, latitude normally comes first, then longitude, as in 19.5362° N, 155.5763° W. Some software and data formats put longitude first, so check the documentation before pasting values.
How far is one degree of latitude?
About 111 km, or 69 miles. One minute is about 1.85 km and one second is about 31 m. A degree of longitude has the same length only at the Equator and shrinks toward the poles.
Why do some coordinates have minus signs?
In decimal form, one number must carry the hemisphere. By convention, south latitudes and west longitudes are negative, so latitude runs from -90 to 90 and longitude from -180 to 180. Letters N, S, E and W do the same job.
Are 19.5362° and 19° 32′ 10″ the same position?
Almost. They are the same position in two notations. Rounding the seconds to a whole number changes the point by a few meters, about 10 m in this case.
How many decimal places do I need?
Two decimals mark a town, about 1.1 km. Four decimals mark a building, about 11 m. Beyond five decimals, the extra digits describe a precision that most maps do not have.
Sources
- How much distance does a degree, minute, and second cover on your maps? U.S. Geological Survey
- Latitude National Geographic Education
- Longitude National Geographic Education
- Mauna Loa Observatory NOAA Global Monitoring Laboratory
- Help: Magnetic Declination Calculator NOAA National Centers for Environmental Information