Understanding maps

Reading hills, valleys and slopes from contour lines

Abstract illustration of a map grid with curved meridians and parallels in blue tones

Picture the sea rising slowly over a hill and pausing at regular heights. At each pause it leaves a waterline around the slope. Draw those waterlines from above and you have contour lines. One geology course describes a contour line in exactly these terms: the shoreline that would exist if the ocean covered the land up to that elevation.

A flat sheet of paper cannot show height directly, so mapmakers have several tricks for it. Ordnance Survey lists spot heights, contours, hachures, hypsometric tints and hill shading. Contours are the one that lets you measure: with a few rules you can read the shape of the land and put a number on its height.

What a contour line and a contour interval are

The USGS defines contours as imaginary lines that join points of equal elevation on the land above or below a reference surface, such as mean sea level. Every point on one line stands at the same height. The contour interval is the vertical distance between two neighboring lines, and it stays the same across a given map. The USGS prints it in the margin, since it is chosen to suit the terrain.

The interval depends on the land. The USGS notes that a flat area may use 10 feet or less, and mountainous areas 100 feet or more. Ordnance Survey gives metric examples: 50 or 100 m where the vertical variation is large, and 5 or 10 m for flatter ground. Every few lines, a thicker index contour carries a printed elevation. According to Ordnance Survey, an index contour often falls on every fifth line, so a map with a 10 m interval would have one every 50 m.

Types of contour line on a topographic map
LineHow it looksWhat it is for
Index contourWider line with an elevation value printed on itLets you read height quickly and count from a known value
Intermediate contourNarrower line between index linesFills in detail between the index lines
Supplementary contourNarrow line added between the othersAdds further detail to the shape of the land
Depression contourClosed line with short ticks pointing inwardMarks a hollow with no outlet

On USGS maps, contours are brown, as explained in map symbols and legends. The geology course adds one exception: contours drawn on glacier surfaces are blue.

Reading hills, valleys, ridges and slopes

Shapes and spacing carry the meaning. Spacing shows steepness: where lines are close together the ground is steep, and where they are far apart it is gentle or flat. Closed loops generally mean hills, with the highest ground inside the smallest loop. Contours never cross, because one point cannot stand at two heights. The only apparent exception is a vertical cliff, where lines may merge, and on very steep slopes mapmakers often break the lines and add a cliff symbol.

Valleys follow the rule of Vs: where contour lines cross a stream, they bend into Vs that point upstream, toward higher ground. On a ridge or spur the bends point the other way, down toward lower ground. This is why contour maps help you trace drainage, a theme developed in rivers and drainage basins.

Contour patterns and what they mean
Pattern on the mapWhat it usually means
Closed loops, one inside anotherA hill or peak, higher toward the center
Closed loops with short inward ticksA depression with no outlet
Lines close togetherA steep slope
Lines far apartA gentle slope or flat ground
Vs that point toward higher ground across a streamA valley, with the stream running through the point and toward the open end of the V
Bends that point toward lower groundA ridge or a spur
Several lines mergingA very steep slope or a cliff

The wider landscape these shapes describe appears in plains, plateaus and valleys. Physical maps use tints and shading instead of contours, as shown in political vs physical maps.

Estimating elevation and slope with worked examples

  1. Find the contour interval in the margin and check its unit.
  2. Locate the nearest labeled index contour.
  3. Count lines up or down from it, adding or subtracting the interval each time.
  4. If your point lies between two lines, estimate between their two values.

Both calculations measure horizontal distance, which is what a map shows. A contour interval also hides small bumps: features smaller than the interval may not appear at all.

How contours compare with other ways of showing relief

Ordnance Survey explains that each method has strengths, and the best choice depends on the scale and the purpose of the map. Contours are widely used and drawn in a neutral color so they do not overpower other features. Many users still find it hard to picture terrain from contours alone, so mapmakers combine them with tints or shading.

Methods of showing relief
MethodStrengthLimit
Spot heightsExact height at one point, such as a summit or a passSays little about the ground between points
ContoursMeasurable elevation and slopeHard to visualize in three dimensions
Hypsometric tintsElevation bands in color, common on small-scale mapsBands are wider than contour intervals
Hill shadingShows slope and shape vividly using simulated lightDoes not show elevation well
HachuresLines along the steepest slope, seen on older mapsCan make a map heavy and cluttered

Scale guides the choice. Large-scale maps lean on contours and spot heights, while hypsometric tints are common on small-scale maps, which cover large areas. Today, tints and shading are usually computed from elevation data rather than drawn by hand. Natural Earth, for instance, derives its shaded relief and elevation tints from NASA elevation data. How such data is gathered is covered in how modern maps are made.

Common mistakes with contour lines

  • Assuming every map uses the same interval

    The interval changes from map to map. Read it in the margin before you convert any line count into height.

  • Confusing close lines with high ground

    Lines packed together mean steep, not high. A plateau can be very high and still have widely spaced lines.

  • Reversing valleys and ridges

    Check the direction of the Vs. A V that points toward higher ground across a stream marks a valley. Bends that point downhill mark a ridge.

  • Mixing units

    Some maps label contours in feet, others in meters. The unit is stated in the margin, and an error here changes every height by a factor of about three.

  • Treating an estimate as a measurement

    Between two lines, elevation is an estimate. For exact heights, look for a labeled spot height.

Frequently asked questions

What is a contour interval?

It is the difference in elevation between two neighboring contour lines. On a map with a 40-foot interval, adjacent lines are always 40 feet apart vertically, however far apart they appear on the page.

Why do contour lines never cross?

A point on the ground cannot be at two heights at once, so two lines of different elevation cannot meet. On a vertical cliff, lines may appear to merge into one.

How do I tell a hill from a depression?

Both appear as closed loops. A depression has short tick marks on the inside of the loop, pointing toward the center, while a hill does not.

What color are contour lines?

On standard USGS topographic maps they are brown, except on glacier surfaces, where they are blue. Contours that show the ocean floor appear in blue or black.

How do I read steepness from a contour map?

Compare the spacing. Close lines mean a steep slope and wide spacing means a gentle one. For a number, divide the interval by the real distance between the lines, using the scale.

Sources

  1. Topographic Map Symbols U.S. Geological Survey
  2. Relief representation (More than Maps: guide to cartography) Ordnance Survey
  3. Reading: Maps (Geology) Lumen Learning, adapted from Wenatchee Valley College Geology 101
  4. Natural Earth: Features Natural Earth

Keep a record of the places you have been, and see what share of the world you have covered.

Open the travel map editor